ACQUISITION OF VARIOUS BRAND-NEW HEAVY EQUIPMENT

Supply and Delivery of Trucks and Heavy Equipment TWO (2) UNITS WHEEL LOADER Engine : 6-Cyl, In-line, 4-cycle, Overhead Camshaft, Watercooled, Turbocharged, Direct Injection, Diesel Displacement : 9.5Ltrs - 9.726Ltrs Torque : At least 970 Nm @ 2000rpm Transmission System : Single-stage four-element, double-turbine hydraulic torque converter, Planetary Power Shift. Braking System: Air over hydraulic disc type Service brake, Electric pneumatic internal expansion shoe type parking brake Output Power : At least 215Ps Bucket Capacity : At least 3 cu.m w/ teeth Operating Weight :17,400-17,500 kgs Rated Load : At least 5,000 kgs Steering System : Load-sensing full hydraulic articulated steering Tipping Load : At least 110 kN Ground Clearance : At least 530 mm Wheel Base : 3,200 - 3,300 mm Dumping Height : At least 3,100 mm Dumping Distance : At least 1,090 mm Dumping Angle : -45 degrees Steering Angle : 33-35 degrees Horizontal Crossing Radius : At least 7230mm Turning Radius : At least 6325mm Breakout Force : At least 175 kN TWO (2) UNITS MOTOR GRADER Engine : 6-Cyl, In-line, 4-cycle, Watercooled, Direct Injection, Diesel Displacement : 6.5Ltrs - 6.75Ltrs Rated Power (Developing) : 142-152 Ps Base Operating / Working Weight : At least 12,100 kgs Transmission System : Counter-shaft, Power shift, Six forward-Three Reverse. Front Wheel Lean : At least 18 degrees Oscillation : At least 15 degrees (Positive & Negative) Turning Radius : At least 6,450mm Steering Arc : At least 50 degrees Frame Articulation : At least 25 degrees Moldbaord Width : At least 3,048 mm Slide Distance (left/right) : At least 500mm Bank slooping angle : At least 85 degrees Ground Clearance : At least 375 mm Cutting Depth : At least 575 mm Tilt Forward : At least 40 degrees Tilt Backward : At least 5 degrees Tractive Force : At least 75 kN Cabin : ROPS/FOPS with aircon Tyre Size : 13.0 x 24 12PR Brakes : Full hydraulic, single loop drum brake. Parking brake : Manual, Inner drum. ONE (1) UNIT ROLLER / VIBRATORY COMPACTOR Engine : 4-Cyl, In-line, 4-cycle, Liquid cooled, Turbocharged, Diesel Output Power : 131-139Ps Displacement : 4.6Ltrs - 4.8Ltrs Electrical System : 12V DC, Negative Ground, 860 CCA Batteries Brakes : Service Brakes (Dynamic Hydrostatic), Parking/Secondary Brake (Spring-applied, Hydraulically released on axle and drum drive motors) Operating Weight : At least 11,200 kg Static Weight @ Drum : At least 6,540 kg Static Weight @ Tires : At least 4,850 kg Frequency : 30 Hz Centrifugal Force (High/Low) : At least 242 kN Nominal Amplitude (High/Low) : At least 1.9 kN Propulsion : Hydrostatic, Single-speed motor on plantary axle with no-spin (right) differential. Two-speed drum drive motor into planetary gear reduction. Travel Speed (High/Low) : 9 kph- 13 kph Cabin : Open Canopy Tire Size : 23.1 x 26 - 8PR Articulation Angle : At least 39 degrees (+/-) Oscillation Angle : At least 15 degrees (+/-) Gradeability : At least 52% ONE (1) UNIT COMPACT WHEEL EXCAVATOR Engine : 4-Cyl, In-line, 4-cycle, Water cooled, Diesel Displacement : 3.1Ltrs - 3.3Ltrs Output Power : At least 53Ps Operating Weight : At least 5,500 kgs Max. Digging Reach : At least 3,492 mm Max Digging Reach on ground : At least 6,105 mm Max. Dumping Height : At least 4,263 mm Bucket Capacity : 0.150 cu.m - 0.2 cu.m ONE (1) UNIT COMPACT CRAWLER EXCAVATOR Engine : 4-Cyl, In-line, 4-cycle, Water cooled, Diesel Displacement : 3.1Ltrs - 3.3Ltrs Output Power : At least 53Ps Operating Weight : At least 8,300 kgs Max. Digging Reach : At least 4,100 mm Max Digging Reach on ground : At least 6,750 mm Max. Dumping Height : At least 4,700 mm Ground Pressure : At least 38 kPa Bucket Capacity : 0.250 cu.m - 0.3 cu.m ONE (1) UNIT BULLDOZER Engine : 6-Cyl, In-line, 4-cycle, Overhead Camshaft, Turbocharged, Diesel Displacement : 9.5Ltrs - 9.726Ltrs Output Power : 183 Ps - 190 Ps Torque : At keast 880 Nm @ 1300 rpm Operating Weight : 17,500 kgs - 19,000 kgs Electrical System : 2 x 12-Volts Min. Ground Clearance : At least 405 mm Ground Pressure : 0.063-0.065 Mpa Min. Turning Radius : At least 3,745 mm Gradeability : 30 degrees Dozing Capacity : 4.5 - 4.7 cu.m Blade Width : At least 3385 mm Blade Height : At least 1145 mm Carrier Rollers : 2 on each side Track Rollers : 7 on each side (4-single flage & 2-double flange.) Track Type : Single-Grouser Shoes (39 on each side) Width of Track Shoe : At least 510mm Pitch : 200 mm - 205 mm Max Pressure of Hydraulic System : At least 21 Mpa ONE (1) UNIT CRAWLER EXCAVATOR Engine : 6-Cyl, In-line, 4-cycle, Overhead Camshaft, Watercooled, Turbocharged, Direct Injection, Charge air cooler, Diesel Output Power : 162 Ps - 170 Ps Torque : At keast 700 Nm @ 1350 rpm Displacement : 5.5 Ltrs - 5.7 Ltrs Bucket Capacity : 1.0 cu.m - 1.25 cu.m Operating Weight : At least 21,100 kgs Electrical System : 24V (2 x 12V) Series Battery Track Pads : At least 2 x 46 Link Pitch : At least 190mm Shoe Width, Triple Grouse : At least 700mm Bottom Rollers : At least 2 x 7 Top Rollers : At least 2 x 2 Boom Range : At least 5.7 m Arm Range : At least 2.9 m Max. Digging Reach : At least 9,930 mm Max. Digging Reach on ground : At least 9,770 mm Max. Dumping Height : At least 6,650 mm Swing System : Axial piston motor, Planetary Gearbox, Automatic holding brake & anti-rebound valve. Max. Slew Speed : At least 12 rpm Slew Torque : At least 76.7 kN-m Cabin : Seal type operator seat, fabric seat, non-air suspension, Aircondition system, manual radio with cassette, sun shield front, roof, rear. Sunlight protection roof. ROPS Certified Cab. ONE (1) UNIT CRAWLER EXCAVATOR LONG REACH Engine : 6-Cyl, In-line, 4-cycle, Overhead Camshaft, Watercooled, Turbocharged, Direct Injection, Charge air cooler, Diesel Output Power : 152 Ps - 159 Ps Torque : At keast 725 Nm @ 1350 rpm Displacement : 5.5Ltrs - 5.7Ltrs Bucket Capacity : 0.5 cu.m - 0.52 cu.m Operating Weight : At least 23,780 kgs Electrical System : 24V (2 x 12V) Series Battery Track Pads : At least 2 x 49 Link Pitch : At least 190mm Shoe Width, Triple Grouse : At least 800mm Bottom Rollers : At least 2 x 8 Top Rollers : At least 2 x 2 Boom Range : At least 8.85 m Arm Range : At least 6.25 m Max. Digging Reach : At least 15,800 mm Max. Digging Reach on ground : At least 15,700 mm Max. Dumping Height : At least 10,950 mm Swing System : Axial piston motor, Planetary Gearbox, Automatic holding brake & anti-rebound valve. Max. Slew Speed : At least 12 rpm Slew Torque : At least 76.7 kN-m Cabin : Seal type operator seat, fabric seat, non-air suspension, Aircondition system, manual radio with cassette, sun shield front, roof, rear. Sunlight protection roof. ROPS Certified Cab. FIVE (5) UNITS 10-WHEELER DUMPTRUCK Engine : 6-Cyl, In-line, 4-cycle, Common Rail, Diesel Displacement : 10.5Ltrs - 10.8Ltrs Output Power : 393 Ps - 397 Ps Torque : At keast 1900 Nm @ 2200 rpm Gross Vehicle Weight : 48,000 kgs - 52,000 kgs Dump Vessel Capacity : 18-20 cu.m Gearbox : 12-speed, Manual Transmission Tire Size : 12.00-R20 Service Brake : Dual circuit pneumatic brake Parking brake : Spring brake Auxillary Brake : Engine Exhaust with ABS Cabin : Standard Single Sleeper with Airconditioning. Power Windows : Equipped with Cruise Control : Equipped with Air Suspended Seat : Equipped with ONE (1) UNIT FUEL TANKER Engine : 4-Cyl, In-line, 4-cycle, Diesel Output Power : 126 Ps - 131 Ps Displacement : 3.7Ltrs - 3.9Ltrs Drive Type : 4x4 6-Wheeler Tank Capacity : Minimum 4KL Transmission System : 8-Speed, Manual Transmission Inclusive of: 3 Years LTO red plate registration, 8" reflectorized LGU logo and "for official use only" markings at sides, 1pc Fire extinguisher Class A,B & C Type(at least 2kg in weight), standard unit tools, Operators training shall be be provided by the supplier at site. Term & Conditions. 1.The Supplier must have its own nearest parts and service center, business office and warehouse to guarantee quick after sales service. Preferably within Region 10 or 11. 2. Supplier must be an ISO 9001:2015 certified company. 3. Delivery of 120 days after issuance of Notice To Proceed (NTP). 4. Appointing of service center is not allowed. 5. The Bidder must have its owned service technicians station within the Province of Bukidnon. 6. All equipments being offered should be of latest model.